Aurora CO Window Replacement provides professional french doors in Aurora, CO for residential and commercial properties across the east Denver metro. French doors trade a sliding panel for two swinging ones, and everything good and bad about them comes from the joint in the middle where they meet.
That joint is the astragal, a vertical member on the inactive leaf, and the active leaf shuts against it. The astragal carries the weatherstrip, takes the shoot bolts top and bottom, and if it is hollow or lightly built it flexes when the wind loads the doors. Almost every drafty french door we are called to look at has a flexing astragal and nothing else wrong with it.
Aurora adds two loads to that joint. The first is wind: downslope gusts off the Front Range push on a pair of doors as one large surface, and the shoot bolts are what stop the leaves from spreading. The second is dryness, because January indoor humidity here runs very low and a wood-cored slab shrinks measurably across a winter.
So we set french doors differently than a page in a humid market would. Shoot bolts get engaged into a real strike in the header and a real socket in the sill, not into a hole drilled in the threshold cap. We shim behind the hinge locations to the full depth of the jamb. And we set the reveal expecting the slab to shrink, not the reverse.
The glass has the divided-lite problem all over again. If you want the classic look, understand that any grille bar held behind the glass becomes a straightedge that shows the deflection every sealed unit carries at this elevation. On large french door lites we push toward exterior applied bars or a clean unobstructed lite, and we explain the reasoning rather than just quoting what was asked for.
There is an honest comparison to make against a slider, and it usually favors the slider in Aurora. A french door needs swing clearance on a deck or patio that is often already crowded with furniture, and an inswing pair eats a corner of the room. If the opening is on a wind-exposed wall, a sliding door is also simply easier to keep tight over time.
Where french doors win is a wide opening you want fully open, and an interior that reads formally. Nothing gives you a clear four or five feet of unobstructed passage the way a swinging pair does, and on a walkout basement or a dining room facing a yard, that is a real change to how the room is used, not a cosmetic one.
Outswing is worth a serious look on this side of the metro and almost nobody offers it. An outswing pair seals against its own stops under wind pressure rather than away from them, which is exactly what you want on an exposed east or north wall, and it gives the interior floor space back. The trade is a threshold detail that has to be done properly.
Our licensed and insured team brings the right materials and equipment to every job — capillary tube vented into the glazing pocket, polyisobutylene primary seal at the spacer edge, silicone secondary seal on a dual-seal unit, molecular sieve desiccant in the spacer channel, soft-coat low-emissivity layer on the third surface, insulating glass sealed at Front Range elevation — and backs the work with a written workmanship warranty. We serve Aurora and nearby communities including Centennial, Parker, Commerce City, Brighton.
What We Handle
Everything our french doors in Aurora covers
One crew, one point of contact, and the full range of french doors work in Aurora, CO. If it is on this list we do it in house rather than handing it to a subcontractor:
- french doors Aurora CO
- french patio door replacement
- inswing french doors
- outswing french doors Colorado
- french door astragal
- double door weatherstrip
- french door glass replacement
- french door hardware
- french door divided lites
- interior french doors
- french door threshold
- french door cost Aurora
- hinged patio door
- french door screen
- french door draft fix
- french door lock alignment
Not sure which one describes your situation? Describe it in plain words and we will sort it out — or browse the rest of our Aurora services.
Materials, equipment and how we do french doors
The difference between french doors that lasts and french doors that gets redone in three years is almost always preparation and materials, not the finish you see on day one. We work with capillary tube vented into the glazing pocket, polyisobutylene primary seal at the spacer edge, silicone secondary seal on a dual-seal unit, molecular sieve desiccant in the spacer channel, spec them to the job instead of to the invoice, and write the material grades into the free estimate so you know exactly what you are buying.
Every Aurora job runs the same way: site walk and measurements, written scope and fixed price, protection of the surrounding area, then the work itself with a daily clean-up. Years of window work in the east Denver metro means we have already met whatever your property is going to throw at us — awkward access, older construction, an HOA with opinions.
Where we do french doors outside Aurora
Aurora CO Window Replacement covers Aurora and the surrounding communities of the east Denver metro. Crews run out to the same nearby cities every week, so an out-of-town job does not mean an out-of-town price.
- French Doors in Centennial, CO — Arapahoe County, population 108,418
- French Doors in Parker, CO — Douglas County, population 58,512
- French Doors in Commerce City, CO — Adams County, population 62,418
- French Doors in Brighton, CO — Adams County, population 40,083
- French Doors in Englewood, CO — Arapahoe County, population 33,659
- French Doors in Littleton, CO — Arapahoe County, population 45,652
Start on the Aurora CO Window Replacement homepage for a free estimate, or call (844) 511-2320 and describe the job.
Why Aurora Chooses Aurora CO Window Replacement
- ✓The elevation of your address goes on the glass order. This city runs from about 5,200 feet along Sand Creek to over 6,200 feet at the south line, and sealed units should be ordered knowing which.
- ✓Argon is quoted as a trade rather than an upgrade. If a unit needs a capillary tube to stay flat at this elevation, the tube vents the gas, so we take the gas off the price instead of charging for it.
- ✓We will tell you when a noise is normal. Manufacturers state that glass deflection at altitude can cause check-rail interference and audible sounds, and that is not a defect you should be paying to replace.
- ✓Glass-only replacement is offered first whenever the frame, the sash and the hardware are sound, because a fogged unit in a good window is a part, not a project, and it costs a fraction of a replacement.
The standards behind french doors
Quality here is not a matter of opinion — it is written down. The french doors work we do in Aurora follows published industry standards: NFRC sets the U-factor and SHGC ratings on every window label, and ENERGY STAR defines the efficiency thresholds by climate zone. If a contractor cannot tell you which standard a detail comes from, that is worth asking about before you sign.
Every french doors project in Aurora gets the same attention, whether it is a single room or a full commercial job. We show up on schedule, keep the site clean, and stand behind the work — the estimate is free and there is no pressure.
Ready to get started? Call (844) 511-2320 for a free french doors free estimate in Aurora, or request a quote and we'll get right back to you.